How does the RCMI converter work?<\/h3><\/div>The integration function of the RCMI converter is essential to balance the output signal of the Rogowski coils and shift it by 90\u00b0. The integrator consists of an active electronic circuit with negligible offset and good linearity. The output voltage signal from the Rogowski coil is converted into a standard 1 A signal. <\/p>\n
The output voltage signal from the passive Rogowski coil is proportional to the frequency of the measured current. The equalizer installed ensures a linear signal to the primary current over a wide frequency range. <\/p>\n
When ordering in conjunction with the RCM Rogowski coil, the primary nominal current must be specified. This results in a fixed transformation ratio, similar to a standard transformer. For example, 1000\/1 A: The main measurement range of 0 to 1000 A is mapped to the secondary measurement range of 0 to 1 A. <\/p>\n<\/div><\/div><\/div>
![](\"https:\/\/www.meierenergy.com\/wp-content\/uploads\/2024\/03\/rcmi-01-03-tores.webp\" "\\"rcmi-01-03-tores\\"")
<\/span><\/div><\/div><\/div><\/div><\/div>Typical applications<\/h3><\/div>- <\/i><\/span>\n
Current measurement for automatic reactive power compensation batteries<\/p>\n<\/div><\/li>
- <\/i><\/span>\n
Current measurement for active harmonic filters<\/p>\n<\/div><\/li>
- <\/i><\/span>\n
Current measurement with existing meters and measurement units (input \/5A or \/1A)<\/p>\n<\/div><\/li>
- <\/i><\/span>\n
Retrofit and measurement in existing installations<\/p>\n<\/div><\/li>
- <\/i><\/span>\n
Metering and sub-metering, energy management systems<\/p>\n<\/div><\/li><\/ul><\/div><\/div><\/div><\/div>
Advantages of the RCMI converter:<\/h3><\/div>- <\/i><\/span>\n
The RCMI converter does not measure direct currents when used with RCM Rogowski coils. Indeed, unlike a standard current transformer (CT), it can accurately measure the alternating current component even if a large superimposed direct current component is present, as there is no iron core to cause saturation. This function is particularly important for measuring ripple currents, for example, in battery charging systems. <\/p>\n<\/div><\/li>
- <\/i><\/span>\n
The RCMI converter has relatively good frequency response characteristics.<\/p>\n<\/div><\/li>
- <\/i><\/span>\n
Compact housing for connecting one RCM coil (RCMI-01) or three RCM coils (RCMI-03).<\/p>\n<\/div><\/li><\/ul>
![\"\"](\"https:\/\/www.meierenergy.com\/wp-content\/uploads\/2024\/03\/rcmi-01-03-schema1.webp\")
<\/div><\/div><\/div>![\"\"](\"https:\/\/www.meierenergy.com\/wp-content\/uploads\/2024\/03\/rcmi-01-03-schema2.webp\")
<\/div><\/div><\/div><\/div><\/i><\/div><\/i><\/div><\/div><\/div><\/div><\/div><\/div><\/div><\/div><\/div>Dimensions<\/h3><\/div>![](\"https:\/\/www.meierenergy.com\/wp-content\/uploads\/2024\/03\/rcmi-01-03-dimensions.webp\" "\\"rcmi-01-03-dimensions\\"")
<\/span><\/div><\/div><\/div><\/div><\/div><\/div><\/div>Technical characteristics<\/h3><\/div>\n\n\n\n\n<\/th>\n RCMI-01<\/th>\n RCMI-03<\/th>\n<\/tr>\n<\/thead>\n \n\nNumber of phases<\/td>\n 1<\/td>\n 3<\/td>\n<\/tr>\n \nNominal output current<\/td>\n 1A AC rms<\/td>\n<\/tr>\n \nMax output current (overload)<\/td>\n 1,5A AC rms<\/td>\n<\/tr>\n \nNominal primary currents (A)<\/td>\n 100, 250, 400, 600, 1000, 1500, 3000, 6000<\/td>\n<\/tr>\n \nTransmission accuracy<\/td>\n 0.5% (at 1% of the nominal primary current @25\u00b0C)<\/td>\n<\/tr>\n \nPhase Error<\/td>\n <= 0.5\u00b0<\/td>\n<\/tr>\n \nLinearity<\/td>\n +\/- 0.2% of measured value (at 10 to 120% of nominal current)<\/td>\n<\/tr>\n \nBandwidth<\/td>\n 30 Hz to 5 kHz<\/td>\n<\/tr>\n \nMax load per phase<\/td>\n 0.5 Ohm<\/td>\n<\/tr>\n \nPower consumption<\/td>\n 10 W<\/td>\n<\/tr>\n \nOutput at 0 A (no drift)<\/td>\n <= 0.01 A<\/td>\n<\/tr>\n \nTemperature drift<\/td>\n 200 ppm\/K<\/td>\n<\/tr>\n \nWeight<\/td>\n 185 g<\/td>\n<\/tr>\n \nDimensions<\/td>\n 114 x 100 x 22.5 mm<\/td>\n<\/tr>\n \nSupply voltage<\/td>\n 12V DC<\/td>\n<\/tr>\n \nOperating temperature range<\/td>\n -30\u00b0C to +70\u00b0C<\/td>\n<\/tr>\n \nStorage temperature range<\/td>\n -30\u00b0C to +70\u00b0C<\/td>\n<\/tr>\n \nRelative humidity<\/td>\n Maximum 80% non-condensing<\/td>\n<\/tr>\n \nProtection<\/td>\n IP 20<\/td>\n<\/tr>\n \nCertification<\/td>\n CE – Cmim<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div><\/div><\/div><\/div><\/div><\/div>Technical characteristics<\/h3><\/div><\/div><\/div>![](\"https:\/\/www.meierenergy.com\/wp-content\/uploads\/2024\/03\/rcmi-01-03-schema.webp\" "\\"rcmi-01-03-schema\\"")
<\/span><\/div><\/div><\/div><\/i><\/span><\/div><\/div><\/div>\nThe output signal (1A) must be exclusively connected to 1A or 5A current transformer inputs that are electrically isolated.<\/p>\n<\/div><\/div><\/div>
<\/i><\/span><\/div><\/div><\/div>\nConnecting the input or output signal to an external voltage is prohibited. Doing so may result in the destruction of the RCMI converter.<\/p>\n<\/div><\/div><\/div>
<\/div><\/div><\/div><\/div><\/div><\/div><\/div><\/div><\/div><\/div>Installation and Connection<\/h3><\/div>\n\n\n\n\nCode<\/th>\n Designation<\/th>\n Nominal current<\/th>\n Rogowski coil compatible<\/th>\n<\/tr>\n<\/thead>\n \n\nRCMI-03-0600M<\/td>\n 1A measurement converter
for 3 Rogowski Coils R-36<\/td>\n 600A<\/td>\n RCM-36<\/td>\n<\/tr>\n \nRCMI-03-1000M<\/td>\n 1A measurement converter
for 3 Rogowski Coils R-100<\/td>\n 1000A<\/td>\n RCM-100<\/td>\n<\/tr>\n \nRCMI-03-3000M<\/td>\n 1A measurement converter
for 3 Rogowski Coils R-150<\/td>\n 3000A<\/td>\n RCM-150<\/td>\n<\/tr>\n \nRCMI-03-6000M<\/td>\n 1A measurement converter
for 3 Rogowski Coils R-200<\/td>\n 6000A<\/td>\n RCM-200<\/td>\n<\/tr>\n \nRCMI-03-1000S<\/td>\n 1A measurement converter
for 3 Rogowski Coils with 100mV\/kA output<\/td>\n 1000A<\/td>\n 3\u00e8me partie -100mV \/ 1kA<\/small><\/td>\n<\/tr>\n\nRCMI-01-0600M<\/td>\n 1A measurement converter
for 1 Rogowski Coil RCM-36<\/td>\n 600A<\/td>\n RCM-36<\/td>\n<\/tr>\n \nRCMI-01-1000M<\/td>\n 1A measurement converter
for 1 Rogowski Coil RCM-100<\/td>\n 1000A<\/td>\n RCM-100<\/td>\n<\/tr>\n \nRCMI-01-3000M<\/td>\n 1A measurement converter
for 1 Rogowski Coil RCM-150<\/td>\n 3000A<\/td>\n RCM-150<\/td>\n<\/tr>\n \nRCMI-01-6000M<\/td>\n 1A measurement converter
for 1 Rogowski Coil RCM-200<\/td>\n 6000A<\/td>\n RCM-200<\/td>\n<\/tr>\n \nRCMI-01-1000S<\/td>\n 1A measurement converter
for 1 Rogowski Coil with 100mV\/kA output<\/td>\n 1000A<\/td>\n 3\u00e8me partie -100mV \/ 1kA<\/small><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div><\/div>
The integration function of the RCMI converter is essential to balance the output signal of the Rogowski coils and shift it by 90\u00b0. The integrator consists of an active electronic circuit with negligible offset and good linearity. The output voltage signal from the Rogowski coil is converted into a standard 1 A signal. <\/p>\n
The output voltage signal from the passive Rogowski coil is proportional to the frequency of the measured current. The equalizer installed ensures a linear signal to the primary current over a wide frequency range. <\/p>\n
When ordering in conjunction with the RCM Rogowski coil, the primary nominal current must be specified. This results in a fixed transformation ratio, similar to a standard transformer. For example, 1000\/1 A: The main measurement range of 0 to 1000 A is mapped to the secondary measurement range of 0 to 1 A. <\/p>\n<\/div><\/div><\/div>
<\/span><\/div><\/div><\/div><\/div><\/div>Typical applications<\/h3><\/div>- <\/i><\/span>\n
Current measurement for automatic reactive power compensation batteries<\/p>\n<\/div><\/li>
- <\/i><\/span>\n
Current measurement for active harmonic filters<\/p>\n<\/div><\/li>
- <\/i><\/span>\n
Current measurement with existing meters and measurement units (input \/5A or \/1A)<\/p>\n<\/div><\/li>
- <\/i><\/span>\n
Retrofit and measurement in existing installations<\/p>\n<\/div><\/li>
- <\/i><\/span>\n
Metering and sub-metering, energy management systems<\/p>\n<\/div><\/li><\/ul><\/div><\/div><\/div><\/div>
Advantages of the RCMI converter:<\/h3><\/div>- <\/i><\/span>\n
The RCMI converter does not measure direct currents when used with RCM Rogowski coils. Indeed, unlike a standard current transformer (CT), it can accurately measure the alternating current component even if a large superimposed direct current component is present, as there is no iron core to cause saturation. This function is particularly important for measuring ripple currents, for example, in battery charging systems. <\/p>\n<\/div><\/li>
- <\/i><\/span>\n
The RCMI converter has relatively good frequency response characteristics.<\/p>\n<\/div><\/li>
- <\/i><\/span>\n
Compact housing for connecting one RCM coil (RCMI-01) or three RCM coils (RCMI-03).<\/p>\n<\/div><\/li><\/ul>
<\/div><\/div><\/div><\/div><\/div><\/div><\/div><\/i><\/div><\/i><\/div><\/div><\/div><\/div><\/div><\/div><\/div><\/div><\/div>Dimensions<\/h3><\/div><\/span><\/div><\/div><\/div><\/div><\/div><\/div><\/div>Technical characteristics<\/h3><\/div>\n\n\n\n\n<\/th>\n RCMI-01<\/th>\n RCMI-03<\/th>\n<\/tr>\n<\/thead>\n \n\nNumber of phases<\/td>\n 1<\/td>\n 3<\/td>\n<\/tr>\n \nNominal output current<\/td>\n 1A AC rms<\/td>\n<\/tr>\n \nMax output current (overload)<\/td>\n 1,5A AC rms<\/td>\n<\/tr>\n \nNominal primary currents (A)<\/td>\n 100, 250, 400, 600, 1000, 1500, 3000, 6000<\/td>\n<\/tr>\n \nTransmission accuracy<\/td>\n 0.5% (at 1% of the nominal primary current @25\u00b0C)<\/td>\n<\/tr>\n \nPhase Error<\/td>\n <= 0.5\u00b0<\/td>\n<\/tr>\n \nLinearity<\/td>\n +\/- 0.2% of measured value (at 10 to 120% of nominal current)<\/td>\n<\/tr>\n \nBandwidth<\/td>\n 30 Hz to 5 kHz<\/td>\n<\/tr>\n \nMax load per phase<\/td>\n 0.5 Ohm<\/td>\n<\/tr>\n \nPower consumption<\/td>\n 10 W<\/td>\n<\/tr>\n \nOutput at 0 A (no drift)<\/td>\n <= 0.01 A<\/td>\n<\/tr>\n \nTemperature drift<\/td>\n 200 ppm\/K<\/td>\n<\/tr>\n \nWeight<\/td>\n 185 g<\/td>\n<\/tr>\n \nDimensions<\/td>\n 114 x 100 x 22.5 mm<\/td>\n<\/tr>\n \nSupply voltage<\/td>\n 12V DC<\/td>\n<\/tr>\n \nOperating temperature range<\/td>\n -30\u00b0C to +70\u00b0C<\/td>\n<\/tr>\n \nStorage temperature range<\/td>\n -30\u00b0C to +70\u00b0C<\/td>\n<\/tr>\n \nRelative humidity<\/td>\n Maximum 80% non-condensing<\/td>\n<\/tr>\n \nProtection<\/td>\n IP 20<\/td>\n<\/tr>\n \nCertification<\/td>\n CE – Cmim<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div><\/div><\/div><\/div><\/div><\/div>Technical characteristics<\/h3><\/div><\/div><\/div><\/span><\/div><\/div><\/div><\/i><\/span><\/div><\/div><\/div>\nThe output signal (1A) must be exclusively connected to 1A or 5A current transformer inputs that are electrically isolated.<\/p>\n<\/div><\/div><\/div>
<\/i><\/span><\/div><\/div><\/div>\nConnecting the input or output signal to an external voltage is prohibited. Doing so may result in the destruction of the RCMI converter.<\/p>\n<\/div><\/div><\/div>
<\/div><\/div><\/div><\/div><\/div><\/div><\/div><\/div><\/div><\/div>Installation and Connection<\/h3><\/div>\n\n\n\n\nCode<\/th>\n Designation<\/th>\n Nominal current<\/th>\n Rogowski coil compatible<\/th>\n<\/tr>\n<\/thead>\n \n\nRCMI-03-0600M<\/td>\n 1A measurement converter
for 3 Rogowski Coils R-36<\/td>\n 600A<\/td>\n RCM-36<\/td>\n<\/tr>\n \nRCMI-03-1000M<\/td>\n 1A measurement converter
for 3 Rogowski Coils R-100<\/td>\n 1000A<\/td>\n RCM-100<\/td>\n<\/tr>\n \nRCMI-03-3000M<\/td>\n 1A measurement converter
for 3 Rogowski Coils R-150<\/td>\n 3000A<\/td>\n RCM-150<\/td>\n<\/tr>\n \nRCMI-03-6000M<\/td>\n 1A measurement converter
for 3 Rogowski Coils R-200<\/td>\n 6000A<\/td>\n RCM-200<\/td>\n<\/tr>\n \nRCMI-03-1000S<\/td>\n 1A measurement converter
for 3 Rogowski Coils with 100mV\/kA output<\/td>\n 1000A<\/td>\n 3\u00e8me partie -100mV \/ 1kA<\/small><\/td>\n<\/tr>\n\nRCMI-01-0600M<\/td>\n 1A measurement converter
for 1 Rogowski Coil RCM-36<\/td>\n 600A<\/td>\n RCM-36<\/td>\n<\/tr>\n \nRCMI-01-1000M<\/td>\n 1A measurement converter
for 1 Rogowski Coil RCM-100<\/td>\n 1000A<\/td>\n RCM-100<\/td>\n<\/tr>\n \nRCMI-01-3000M<\/td>\n 1A measurement converter
for 1 Rogowski Coil RCM-150<\/td>\n 3000A<\/td>\n RCM-150<\/td>\n<\/tr>\n \nRCMI-01-6000M<\/td>\n 1A measurement converter
for 1 Rogowski Coil RCM-200<\/td>\n 6000A<\/td>\n RCM-200<\/td>\n<\/tr>\n \nRCMI-01-1000S<\/td>\n 1A measurement converter
for 1 Rogowski Coil with 100mV\/kA output<\/td>\n 1000A<\/td>\n 3\u00e8me partie -100mV \/ 1kA<\/small><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div><\/div>
Current measurement for automatic reactive power compensation batteries<\/p>\n<\/div><\/li>
Current measurement for active harmonic filters<\/p>\n<\/div><\/li>
Current measurement with existing meters and measurement units (input \/5A or \/1A)<\/p>\n<\/div><\/li>
Retrofit and measurement in existing installations<\/p>\n<\/div><\/li>
Metering and sub-metering, energy management systems<\/p>\n<\/div><\/li><\/ul><\/div><\/div><\/div><\/div>
Advantages of the RCMI converter:<\/h3><\/div>- <\/i><\/span>\n
The RCMI converter does not measure direct currents when used with RCM Rogowski coils. Indeed, unlike a standard current transformer (CT), it can accurately measure the alternating current component even if a large superimposed direct current component is present, as there is no iron core to cause saturation. This function is particularly important for measuring ripple currents, for example, in battery charging systems. <\/p>\n<\/div><\/li>
- <\/i><\/span>\n
The RCMI converter has relatively good frequency response characteristics.<\/p>\n<\/div><\/li>
- <\/i><\/span>\n
Compact housing for connecting one RCM coil (RCMI-01) or three RCM coils (RCMI-03).<\/p>\n<\/div><\/li><\/ul>
<\/div><\/div><\/div><\/div><\/div><\/div><\/div><\/i><\/div><\/i><\/div><\/div><\/div><\/div><\/div><\/div><\/div><\/div><\/div>Dimensions<\/h3><\/div><\/span><\/div><\/div><\/div><\/div><\/div><\/div><\/div>Technical characteristics<\/h3><\/div>\n\n\n\n\n<\/th>\n RCMI-01<\/th>\n RCMI-03<\/th>\n<\/tr>\n<\/thead>\n \n\nNumber of phases<\/td>\n 1<\/td>\n 3<\/td>\n<\/tr>\n \nNominal output current<\/td>\n 1A AC rms<\/td>\n<\/tr>\n \nMax output current (overload)<\/td>\n 1,5A AC rms<\/td>\n<\/tr>\n \nNominal primary currents (A)<\/td>\n 100, 250, 400, 600, 1000, 1500, 3000, 6000<\/td>\n<\/tr>\n \nTransmission accuracy<\/td>\n 0.5% (at 1% of the nominal primary current @25\u00b0C)<\/td>\n<\/tr>\n \nPhase Error<\/td>\n <= 0.5\u00b0<\/td>\n<\/tr>\n \nLinearity<\/td>\n +\/- 0.2% of measured value (at 10 to 120% of nominal current)<\/td>\n<\/tr>\n \nBandwidth<\/td>\n 30 Hz to 5 kHz<\/td>\n<\/tr>\n \nMax load per phase<\/td>\n 0.5 Ohm<\/td>\n<\/tr>\n \nPower consumption<\/td>\n 10 W<\/td>\n<\/tr>\n \nOutput at 0 A (no drift)<\/td>\n <= 0.01 A<\/td>\n<\/tr>\n \nTemperature drift<\/td>\n 200 ppm\/K<\/td>\n<\/tr>\n \nWeight<\/td>\n 185 g<\/td>\n<\/tr>\n \nDimensions<\/td>\n 114 x 100 x 22.5 mm<\/td>\n<\/tr>\n \nSupply voltage<\/td>\n 12V DC<\/td>\n<\/tr>\n \nOperating temperature range<\/td>\n -30\u00b0C to +70\u00b0C<\/td>\n<\/tr>\n \nStorage temperature range<\/td>\n -30\u00b0C to +70\u00b0C<\/td>\n<\/tr>\n \nRelative humidity<\/td>\n Maximum 80% non-condensing<\/td>\n<\/tr>\n \nProtection<\/td>\n IP 20<\/td>\n<\/tr>\n \nCertification<\/td>\n CE – Cmim<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div><\/div><\/div><\/div><\/div><\/div>Technical characteristics<\/h3><\/div><\/div><\/div><\/span><\/div><\/div><\/div><\/i><\/span><\/div><\/div><\/div>\nThe output signal (1A) must be exclusively connected to 1A or 5A current transformer inputs that are electrically isolated.<\/p>\n<\/div><\/div><\/div>
<\/i><\/span><\/div><\/div><\/div>\nConnecting the input or output signal to an external voltage is prohibited. Doing so may result in the destruction of the RCMI converter.<\/p>\n<\/div><\/div><\/div>
<\/div><\/div><\/div><\/div><\/div><\/div><\/div><\/div><\/div><\/div>Installation and Connection<\/h3><\/div>\n\n\n\n\nCode<\/th>\n Designation<\/th>\n Nominal current<\/th>\n Rogowski coil compatible<\/th>\n<\/tr>\n<\/thead>\n \n\nRCMI-03-0600M<\/td>\n 1A measurement converter
for 3 Rogowski Coils R-36<\/td>\n 600A<\/td>\n RCM-36<\/td>\n<\/tr>\n \nRCMI-03-1000M<\/td>\n 1A measurement converter
for 3 Rogowski Coils R-100<\/td>\n 1000A<\/td>\n RCM-100<\/td>\n<\/tr>\n \nRCMI-03-3000M<\/td>\n 1A measurement converter
for 3 Rogowski Coils R-150<\/td>\n 3000A<\/td>\n RCM-150<\/td>\n<\/tr>\n \nRCMI-03-6000M<\/td>\n 1A measurement converter
for 3 Rogowski Coils R-200<\/td>\n 6000A<\/td>\n RCM-200<\/td>\n<\/tr>\n \nRCMI-03-1000S<\/td>\n 1A measurement converter
for 3 Rogowski Coils with 100mV\/kA output<\/td>\n 1000A<\/td>\n 3\u00e8me partie -100mV \/ 1kA<\/small><\/td>\n<\/tr>\n\nRCMI-01-0600M<\/td>\n 1A measurement converter
for 1 Rogowski Coil RCM-36<\/td>\n 600A<\/td>\n RCM-36<\/td>\n<\/tr>\n \nRCMI-01-1000M<\/td>\n 1A measurement converter
for 1 Rogowski Coil RCM-100<\/td>\n 1000A<\/td>\n RCM-100<\/td>\n<\/tr>\n \nRCMI-01-3000M<\/td>\n 1A measurement converter
for 1 Rogowski Coil RCM-150<\/td>\n 3000A<\/td>\n RCM-150<\/td>\n<\/tr>\n \nRCMI-01-6000M<\/td>\n 1A measurement converter
for 1 Rogowski Coil RCM-200<\/td>\n 6000A<\/td>\n RCM-200<\/td>\n<\/tr>\n \nRCMI-01-1000S<\/td>\n 1A measurement converter
for 1 Rogowski Coil with 100mV\/kA output<\/td>\n 1000A<\/td>\n 3\u00e8me partie -100mV \/ 1kA<\/small><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div><\/div>
The RCMI converter does not measure direct currents when used with RCM Rogowski coils. Indeed, unlike a standard current transformer (CT), it can accurately measure the alternating current component even if a large superimposed direct current component is present, as there is no iron core to cause saturation. This function is particularly important for measuring ripple currents, for example, in battery charging systems. <\/p>\n<\/div><\/li>
The RCMI converter has relatively good frequency response characteristics.<\/p>\n<\/div><\/li>
Compact housing for connecting one RCM coil (RCMI-01) or three RCM coils (RCMI-03).<\/p>\n<\/div><\/li><\/ul>
<\/div><\/div><\/div><\/div><\/div><\/div><\/div>Dimensions<\/h3><\/div><\/span><\/div><\/div><\/div><\/div><\/div><\/div><\/div>Technical characteristics<\/h3><\/div>\n\n\n\n\n<\/th>\n RCMI-01<\/th>\n RCMI-03<\/th>\n<\/tr>\n<\/thead>\n \n\nNumber of phases<\/td>\n 1<\/td>\n 3<\/td>\n<\/tr>\n \nNominal output current<\/td>\n 1A AC rms<\/td>\n<\/tr>\n \nMax output current (overload)<\/td>\n 1,5A AC rms<\/td>\n<\/tr>\n \nNominal primary currents (A)<\/td>\n 100, 250, 400, 600, 1000, 1500, 3000, 6000<\/td>\n<\/tr>\n \nTransmission accuracy<\/td>\n 0.5% (at 1% of the nominal primary current @25\u00b0C)<\/td>\n<\/tr>\n \nPhase Error<\/td>\n <= 0.5\u00b0<\/td>\n<\/tr>\n \nLinearity<\/td>\n +\/- 0.2% of measured value (at 10 to 120% of nominal current)<\/td>\n<\/tr>\n \nBandwidth<\/td>\n 30 Hz to 5 kHz<\/td>\n<\/tr>\n \nMax load per phase<\/td>\n 0.5 Ohm<\/td>\n<\/tr>\n \nPower consumption<\/td>\n 10 W<\/td>\n<\/tr>\n \nOutput at 0 A (no drift)<\/td>\n <= 0.01 A<\/td>\n<\/tr>\n \nTemperature drift<\/td>\n 200 ppm\/K<\/td>\n<\/tr>\n \nWeight<\/td>\n 185 g<\/td>\n<\/tr>\n \nDimensions<\/td>\n 114 x 100 x 22.5 mm<\/td>\n<\/tr>\n \nSupply voltage<\/td>\n 12V DC<\/td>\n<\/tr>\n \nOperating temperature range<\/td>\n -30\u00b0C to +70\u00b0C<\/td>\n<\/tr>\n \nStorage temperature range<\/td>\n -30\u00b0C to +70\u00b0C<\/td>\n<\/tr>\n \nRelative humidity<\/td>\n Maximum 80% non-condensing<\/td>\n<\/tr>\n \nProtection<\/td>\n IP 20<\/td>\n<\/tr>\n \nCertification<\/td>\n CE – Cmim<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div><\/div><\/div><\/div><\/div><\/div>Technical characteristics<\/h3><\/div><\/div><\/div><\/span><\/div><\/div><\/div><\/i><\/span><\/div><\/div><\/div>\nThe output signal (1A) must be exclusively connected to 1A or 5A current transformer inputs that are electrically isolated.<\/p>\n<\/div><\/div><\/div>
<\/i><\/span><\/div><\/div><\/div>\nConnecting the input or output signal to an external voltage is prohibited. Doing so may result in the destruction of the RCMI converter.<\/p>\n<\/div><\/div><\/div>
<\/div><\/div><\/div><\/div><\/div><\/div><\/div><\/div><\/div><\/div>Installation and Connection<\/h3><\/div>\n\n\n\n\nCode<\/th>\n Designation<\/th>\n Nominal current<\/th>\n Rogowski coil compatible<\/th>\n<\/tr>\n<\/thead>\n \n\nRCMI-03-0600M<\/td>\n 1A measurement converter
for 3 Rogowski Coils R-36<\/td>\n 600A<\/td>\n RCM-36<\/td>\n<\/tr>\n \nRCMI-03-1000M<\/td>\n 1A measurement converter
for 3 Rogowski Coils R-100<\/td>\n 1000A<\/td>\n RCM-100<\/td>\n<\/tr>\n \nRCMI-03-3000M<\/td>\n 1A measurement converter
for 3 Rogowski Coils R-150<\/td>\n 3000A<\/td>\n RCM-150<\/td>\n<\/tr>\n \nRCMI-03-6000M<\/td>\n 1A measurement converter
for 3 Rogowski Coils R-200<\/td>\n 6000A<\/td>\n RCM-200<\/td>\n<\/tr>\n \nRCMI-03-1000S<\/td>\n 1A measurement converter
for 3 Rogowski Coils with 100mV\/kA output<\/td>\n 1000A<\/td>\n 3\u00e8me partie -100mV \/ 1kA<\/small><\/td>\n<\/tr>\n\nRCMI-01-0600M<\/td>\n 1A measurement converter
for 1 Rogowski Coil RCM-36<\/td>\n 600A<\/td>\n RCM-36<\/td>\n<\/tr>\n \nRCMI-01-1000M<\/td>\n 1A measurement converter
for 1 Rogowski Coil RCM-100<\/td>\n 1000A<\/td>\n RCM-100<\/td>\n<\/tr>\n \nRCMI-01-3000M<\/td>\n 1A measurement converter
for 1 Rogowski Coil RCM-150<\/td>\n 3000A<\/td>\n RCM-150<\/td>\n<\/tr>\n \nRCMI-01-6000M<\/td>\n 1A measurement converter
for 1 Rogowski Coil RCM-200<\/td>\n 6000A<\/td>\n RCM-200<\/td>\n<\/tr>\n \nRCMI-01-1000S<\/td>\n 1A measurement converter
for 1 Rogowski Coil with 100mV\/kA output<\/td>\n 1000A<\/td>\n 3\u00e8me partie -100mV \/ 1kA<\/small><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div><\/div>
<\/span><\/div>Technical characteristics<\/h3><\/div>\n\n\n\n\n<\/th>\n RCMI-01<\/th>\n RCMI-03<\/th>\n<\/tr>\n<\/thead>\n \n\nNumber of phases<\/td>\n 1<\/td>\n 3<\/td>\n<\/tr>\n \nNominal output current<\/td>\n 1A AC rms<\/td>\n<\/tr>\n \nMax output current (overload)<\/td>\n 1,5A AC rms<\/td>\n<\/tr>\n \nNominal primary currents (A)<\/td>\n 100, 250, 400, 600, 1000, 1500, 3000, 6000<\/td>\n<\/tr>\n \nTransmission accuracy<\/td>\n 0.5% (at 1% of the nominal primary current @25\u00b0C)<\/td>\n<\/tr>\n \nPhase Error<\/td>\n <= 0.5\u00b0<\/td>\n<\/tr>\n \nLinearity<\/td>\n +\/- 0.2% of measured value (at 10 to 120% of nominal current)<\/td>\n<\/tr>\n \nBandwidth<\/td>\n 30 Hz to 5 kHz<\/td>\n<\/tr>\n \nMax load per phase<\/td>\n 0.5 Ohm<\/td>\n<\/tr>\n \nPower consumption<\/td>\n 10 W<\/td>\n<\/tr>\n \nOutput at 0 A (no drift)<\/td>\n <= 0.01 A<\/td>\n<\/tr>\n \nTemperature drift<\/td>\n 200 ppm\/K<\/td>\n<\/tr>\n \nWeight<\/td>\n 185 g<\/td>\n<\/tr>\n \nDimensions<\/td>\n 114 x 100 x 22.5 mm<\/td>\n<\/tr>\n \nSupply voltage<\/td>\n 12V DC<\/td>\n<\/tr>\n \nOperating temperature range<\/td>\n -30\u00b0C to +70\u00b0C<\/td>\n<\/tr>\n \nStorage temperature range<\/td>\n -30\u00b0C to +70\u00b0C<\/td>\n<\/tr>\n \nRelative humidity<\/td>\n Maximum 80% non-condensing<\/td>\n<\/tr>\n \nProtection<\/td>\n IP 20<\/td>\n<\/tr>\n \nCertification<\/td>\n CE – Cmim<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div><\/div><\/div><\/div><\/div><\/div>Technical characteristics<\/h3><\/div><\/div><\/div><\/span><\/div><\/div><\/div><\/i><\/span><\/div><\/div><\/div>\nThe output signal (1A) must be exclusively connected to 1A or 5A current transformer inputs that are electrically isolated.<\/p>\n<\/div><\/div><\/div>
<\/i><\/span><\/div><\/div><\/div>\nConnecting the input or output signal to an external voltage is prohibited. Doing so may result in the destruction of the RCMI converter.<\/p>\n<\/div><\/div><\/div>
<\/div><\/div><\/div><\/div><\/div><\/div><\/div><\/div><\/div><\/div>Installation and Connection<\/h3><\/div>\n\n\n\n\nCode<\/th>\n Designation<\/th>\n Nominal current<\/th>\n Rogowski coil compatible<\/th>\n<\/tr>\n<\/thead>\n \n\nRCMI-03-0600M<\/td>\n 1A measurement converter
for 3 Rogowski Coils R-36<\/td>\n 600A<\/td>\n RCM-36<\/td>\n<\/tr>\n \nRCMI-03-1000M<\/td>\n 1A measurement converter
for 3 Rogowski Coils R-100<\/td>\n 1000A<\/td>\n RCM-100<\/td>\n<\/tr>\n \nRCMI-03-3000M<\/td>\n 1A measurement converter
for 3 Rogowski Coils R-150<\/td>\n 3000A<\/td>\n RCM-150<\/td>\n<\/tr>\n \nRCMI-03-6000M<\/td>\n 1A measurement converter
for 3 Rogowski Coils R-200<\/td>\n 6000A<\/td>\n RCM-200<\/td>\n<\/tr>\n \nRCMI-03-1000S<\/td>\n 1A measurement converter
for 3 Rogowski Coils with 100mV\/kA output<\/td>\n 1000A<\/td>\n 3\u00e8me partie -100mV \/ 1kA<\/small><\/td>\n<\/tr>\n\nRCMI-01-0600M<\/td>\n 1A measurement converter
for 1 Rogowski Coil RCM-36<\/td>\n 600A<\/td>\n RCM-36<\/td>\n<\/tr>\n \nRCMI-01-1000M<\/td>\n 1A measurement converter
for 1 Rogowski Coil RCM-100<\/td>\n 1000A<\/td>\n RCM-100<\/td>\n<\/tr>\n \nRCMI-01-3000M<\/td>\n 1A measurement converter
for 1 Rogowski Coil RCM-150<\/td>\n 3000A<\/td>\n RCM-150<\/td>\n<\/tr>\n \nRCMI-01-6000M<\/td>\n 1A measurement converter
for 1 Rogowski Coil RCM-200<\/td>\n 6000A<\/td>\n RCM-200<\/td>\n<\/tr>\n \nRCMI-01-1000S<\/td>\n 1A measurement converter
for 1 Rogowski Coil with 100mV\/kA output<\/td>\n 1000A<\/td>\n 3\u00e8me partie -100mV \/ 1kA<\/small><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div><\/div>
| <\/th>\n | RCMI-01<\/th>\n | RCMI-03<\/th>\n<\/tr>\n<\/thead>\n | |||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Number of phases<\/td>\n | 1<\/td>\n | 3<\/td>\n<\/tr>\n | |||||||||||||||||||||||||||||||||||||||||||
| Nominal output current<\/td>\n | 1A AC rms<\/td>\n<\/tr>\n | ||||||||||||||||||||||||||||||||||||||||||||
| Max output current (overload)<\/td>\n | 1,5A AC rms<\/td>\n<\/tr>\n | ||||||||||||||||||||||||||||||||||||||||||||
| Nominal primary currents (A)<\/td>\n | 100, 250, 400, 600, 1000, 1500, 3000, 6000<\/td>\n<\/tr>\n | ||||||||||||||||||||||||||||||||||||||||||||
| Transmission accuracy<\/td>\n | 0.5% (at 1% of the nominal primary current @25\u00b0C)<\/td>\n<\/tr>\n | ||||||||||||||||||||||||||||||||||||||||||||
| Phase Error<\/td>\n | <= 0.5\u00b0<\/td>\n<\/tr>\n | ||||||||||||||||||||||||||||||||||||||||||||
| Linearity<\/td>\n | +\/- 0.2% of measured value (at 10 to 120% of nominal current)<\/td>\n<\/tr>\n | ||||||||||||||||||||||||||||||||||||||||||||
| Bandwidth<\/td>\n | 30 Hz to 5 kHz<\/td>\n<\/tr>\n | ||||||||||||||||||||||||||||||||||||||||||||
| Max load per phase<\/td>\n | 0.5 Ohm<\/td>\n<\/tr>\n | ||||||||||||||||||||||||||||||||||||||||||||
| Power consumption<\/td>\n | 10 W<\/td>\n<\/tr>\n | ||||||||||||||||||||||||||||||||||||||||||||
| Output at 0 A (no drift)<\/td>\n | <= 0.01 A<\/td>\n<\/tr>\n | ||||||||||||||||||||||||||||||||||||||||||||
| Temperature drift<\/td>\n | 200 ppm\/K<\/td>\n<\/tr>\n | ||||||||||||||||||||||||||||||||||||||||||||
| Weight<\/td>\n | 185 g<\/td>\n<\/tr>\n | ||||||||||||||||||||||||||||||||||||||||||||
| Dimensions<\/td>\n | 114 x 100 x 22.5 mm<\/td>\n<\/tr>\n | ||||||||||||||||||||||||||||||||||||||||||||
| Supply voltage<\/td>\n | 12V DC<\/td>\n<\/tr>\n | ||||||||||||||||||||||||||||||||||||||||||||
| Operating temperature range<\/td>\n | -30\u00b0C to +70\u00b0C<\/td>\n<\/tr>\n | ||||||||||||||||||||||||||||||||||||||||||||
| Storage temperature range<\/td>\n | -30\u00b0C to +70\u00b0C<\/td>\n<\/tr>\n | ||||||||||||||||||||||||||||||||||||||||||||
| Relative humidity<\/td>\n | Maximum 80% non-condensing<\/td>\n<\/tr>\n | ||||||||||||||||||||||||||||||||||||||||||||
| Protection<\/td>\n | IP 20<\/td>\n<\/tr>\n | ||||||||||||||||||||||||||||||||||||||||||||
| Certification<\/td>\n | CE – Cmim<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n <\/div><\/div><\/div><\/div><\/div><\/div> Technical characteristics<\/h3><\/div><\/div><\/div><\/span><\/div><\/div><\/div><\/i><\/span><\/div><\/div> <\/div> \n The output signal (1A) must be exclusively connected to 1A or 5A current transformer inputs that are electrically isolated.<\/p>\n<\/div><\/div><\/div> <\/i><\/span><\/div><\/div> <\/div> \n Connecting the input or output signal to an external voltage is prohibited. Doing so may result in the destruction of the RCMI converter.<\/p>\n<\/div><\/div><\/div> <\/div><\/div><\/div><\/div> <\/div><\/div><\/div><\/div><\/div><\/div> Installation and Connection<\/h3><\/div>\n
|